The Conclusions and Recommendations could be combined or, in long reports, presented in separate sections.

The Conclusions and Recommendations could be combined or, in long reports, presented in separate sections.

Conclusions and recommendations

If there aren’t any recommendations to be made because of the project, just call this section Conclusions.

The Conclusions section sums up one of the keys points of the discussion, the primary options that come with your design, or the significant outcomes of the investigation. As its function is always to round from the story of any project, it should:

  • be written to relate straight to the aims associated with project as previously mentioned in the Introduction
  • indicate the extent to that the aims have already been achieved
  • summarise the key findings, outcomes or information in your report
  • acknowledge limitations and also make suggestions for future work (where applicable)
  • highlight the significance or usefulness of the work.

The conclusions should relate to the aims of this work:

The purpose of this project is always to design a mobile phone tower for a suburban location..

The cellular phone tower presented here could be erected safely in a suburban street.

It takes an overall total section of a maximum of 2m 2 l, and contains the following safety features.

This investigation will review the quantity of passengers utilizing the Monash University Clayton-Caulfield inter-campus bus in order to recommend adjustments towards the ongoing service if needed.

Analysis of this survey data obtained in this project demonstrates that use of the Clayton-Caulfield inter-campus bus has grown by 24% in the past five years. It is strongly recommended that frequency be increased during peak usage.

The Conclusions section below is from a known level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Go through the buttons that are coloured start to see the comments.

Conclusions

ninjaessays writing service

All the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the discussion that is preceding. In this full case, in addition indicates that the aims regarding the project have now been met. presented in this report fulfil the criteria specified into the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this full case the key options that come with the designs – are then recapped. Incorporate piers that are round piled foundations, which are used because the soil conditions are unknown and possibly unstable. Design 1, a straightforward composite I-girder bridge, gets the benefit of being made of steel and so has longer spans and fewer piers.

Design 2, a super-T beam br >Design 2 Lecturer’s comment:
The significance of the results – in cases like this the final recommendation – is clearly stated. is therefore recommended. It gives Lecturer’s comment:
To finish off, the achievement of this project is reinforced. An overpass that is affordable superior durability, and fully meets the requirements associated with design brief.

Always address limitations and suggest how they might be overcome in future work. The excerpt below is through the Conclusions of a written report on a project investigating the end result of pulsation on heat transfer in horizontal pipe flow.

Experimental results Lecturer’s comment:
Key conclusions drawn through the project. indicated that pulsed flow without flow reversal had no significant effect compared with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. That is likely due Lecturer’s comment:
Provide a explanation that is possible notable results, especially unexpected ones. to the large disturbances in the hydrodynamic boundary layer when the flow changes direction. Further research Lecturer’s comment:
Recommend further research to address any work that is extra think would be useful. is recommended to determine the maximum enhancement that is achievable.

It must be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations and/or solutions. the experimental results try not to concur with the theoretical equations. This might be as a result of the deposits which developed within the pipe, or to thermocouple temperature that is inconsistent. Therefore, regular inspection associated with the test rig is recommended.

For a tremendously report that is long it is acceptable to provide the conclusions and recommendations in point form:

The prototype robot courier presented here has been confirmed to manage to delivering documents autonomously in an office environment. It has demonstrated the next components of mobile robotics:

  1. Localisation: The Kalman localisation that is filter-based achieved sub-centimeter accuracy under normal operating conditions.
  2. Environment modelling: The occupancy map was updated dynamically to include obstacles not contained in the original map.
  3. Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free way to the target.

Leave a Reply

Your email address will not be published. Required fields are marked *